TECHNIQUE FAQ: Fixing broken pressed-powder products

martygreene

Well-known member
Standard Method:
  • Soak the broken product in alcohol to make paste
  • Smooth out with your finger wrapped in saran wrap, using only the tip, minimize contact. Paste will be dark.
At this point, you can simply allow to dry undisturbed for 2-3 days by air, or continue by doing the following:
  • Bake in increments of 3 minutes in oven preheated to 200 degrees Fahrenheit (93 degree centigrade). Be sure to stabilize the pan of product on some foil whilst baking. Do NOT use a heat-conductive platform such as a cookie sheet.
  • Watching non-stop, do this until paste just begins to lighten, signaling evaporation of alcohol. Any shortcuts or leaving the product alone for even a few minutes could result in over-heating and alteration in color.
  • When lightening begins, remove from oven and let sit undisturbed at room temperature for 2 days. The product will be a little lumpy, but recovered.

Method #2:
  • Collect all the broken product onto a piece of paper.
  • Create a funnel with the paper and then pour the powder back into the pan.
  • Using plastic wrap and your index finger, push all the powder back into the pan with medium force. Keep on pushing until the powder is flat.

Method #3:
  • Arrange all of the broken pieces back into the pot, and lay a tissue over the pieces.
  • Take the end of a bottle (the old-style MAC hyper real bottle caps worked perfectly for MAC and similarly sized shadows) and press over the tissue with the bottle or bottle cap.
  • Remove the tissue, and the product will be perfectly pressed back into the pot and the surface will be as smooth.

Adding Hatch Marks:
This should be done just as the product is still damp but NOT pasty from repair with alcohol (you should be able to press on it with your fingers).
  • Get a piece of wax paper over your shadow and firmly press down all over the e/s making sure it is set firmly and the surface is an even as possible.
  • If you see cracks, lightly spray with alcohol and press again using your finger or wax paper.
  • Take an old pair of coarse jeans and turn them inside out. (Levi's work well, as do any other thick heavily textured material)
  • Carefully take one of the inside out legs and put it over the surface and press firmly all over.
  • Voila! You have the pretty hatch mark you lost in breakage. If the imprint is not showing as much as you want, spray with alcohol and press again or press harder.

Making Your Broken Product Into a Loose Powder:
Instead of trying to stuff the broken product into the pan, you can just make it all into loose powder.
  • Get a small mortar and pestle (available from kitchen stores) and put all of the product into it, scraping out the unbroken remnants if desired.
  • Grind product as finely as possible.
  • Put the loose powder in a small tin or tub, and apply using a brush.
 

missBOMBcheLLe

Well-known member
its sux cuz i after reading this post yesterday i started depotting my blushes... after i was done with a dual blush, i stuck the sticker in the back, half of the blush cracked into pieces
ssad.gif


how can i just fix half of it? and what kind of alcohol do i use (rubbing alcohol)?
 

martygreene

Well-known member
I would follow the standard method, without baking, and just be sure to allow it to dry thoroughly before using it again.

Yes, rubbing alcohol- preferrably the unscented kind. I would just alcohol the portion which was damaged.
 

Janice

Well-known member
Quote:
Originally Posted by redbombchelle
also, how do i post pictures up?

The FAQ for that is listed here
 

Guccii

Member
I tried the #1 method last thursday and its still kinda wet and pastey, is there anything I can do to fix it? I was thinking about putting it in the oven for a few more minutes, but I dont want to ruin it!

I did three at once, and the other two are great!

Thanks for the tutorial!!
 

martygreene

Well-known member
Some products can take a while to dry, and it also depends on the percentage of alcohol in the rubbing alchohol that is used. You can probably try baking it as described above for a short bit to help speed it along.
 

Isis

Well-known member
Actually, while I was watching Stripped a few nights ago on the Style Network, they showed how manufactures get their hatch marks.
All they do place a small square of silk over the pans before they're pressed
smiles.gif


Throught you'd like to know.
 

cyens

Well-known member
I have a question

I've been reading that heating make-up is very bad because it destroys the preservatives inside the product. Which could result in bacterial spred or other deteriorations
I even read that the heat inside your car in summer in the sun is enough to alterate your make-up. I forgot though whats the maximum heat your make-up can stand before it destroys products inside of it, but its not very high.
 

als1626

Active member
Do you think this process would work on a broken, pretty much new MSF? Or is there too much product to do this? Would it be better to crush the MSF with a mortar and pestle and use it as a loose powder, or would that be too messy? Thanks for the great info!
 

kalice

Well-known member
I tried fixing a matte finish eyeshadow (either soulsong or endless love I can't remember the name) with the alcohol method. I used 70% isopropanol and let it dry for five days and I ended up with this lumpy, incredibly chalky thing after. I couldn't get any colour pay off (it was so hard!). I've fixed other finishes (lustre, frosts etc) and the texture doesn't change, but is it different with mattes?

Ack, the chalkiness on this repaired matte is ridiculous, it's like a rock! Any suggestions to what i can do with it?
 

pearl

Well-known member
Thank you soo sooo much for this! I have a few broken e/s's. I'll try some of these later. =)
 

crimsonette

Well-known member
i, too, am concerned about how this will go with a matte shadow. my carbon committed makeup seppuku when i was depotting it, and it just seems to me that maybe matte shadows won't work the same?
 

girlsaidwhat

Well-known member
My last carbon es broke. I did the "put the pieces back in the pan and press real hard without adding anything" method
winks.gif
and it worked just fine (saran wrapped finger to preserve product). I wouldn't take it out of the house or anything, but it kept together until I used it up.

Quote:
Originally Posted by crimsonette
i, too, am concerned about how this will go with a matte shadow. my carbon committed makeup seppuku when i was depotting it, and it just seems to me that maybe matte shadows won't work the same?
 

Whitney

Active member
Thanks! I never knew there was methods to actually putting makeup back together...I've lost so much product before by them breaking up.
 

Latest posts

Top